Exterior lights

Warning

•

Make sure to always keep your low beam on in dark driving conditions. Failure to do so is both illegal and very dangerous, and can result in an accident leading to death or serious injury.

•

Use adaptive driving beam or make sure to manually turn off your high beam when coming close to other cars. Failure to do so could blind your fellow road users, which could result in an accident, causing death or serious injury.

•

Make sure to check that all exterior lights work before driving. While the car will usually notice on its own that a light has failed, it is the responsibility of the driver to know that all lights are working. Driving with broken lights is dangerous and can be illegal.

The exterior lights are controlled by the left stalk, the center display, and the hazard warning lights button on the overhead console.

Left stalk light controls

The left stalk is used to control the high beam and the direction indicator lights.

High beam

To control the high beam with the left stalk:

•

Move the stalk forward/backward to turn on/off the high beam. Move the stalk forward again to switch between manual high beam and adaptive driving beam.

•

Pull the stalk backward to flash the high beam.

Adaptive driving beam automatically dims parts of the high beam to prevent blinding oncoming traffic, while still keeping the road ahead illuminated. Adaptive driving beam is automatically turned on if the sourroundings are dark and the speed is at least 30 km/h. The exterior lights settings need to be set to

for the adaptive driving beam to activate.

When adaptive driving beam is active, returning the stalk to the neutral position resumes adaptive driving beam. This means that the high beam can still be active if the stalk is returned to the neutral position, as long as the system is not detecting oncoming traffic.

Note: The high beam can only be used when the car is in driving mode and the low beam is turned on.

Indicator lights

The indicator lights are controlled by the left stalk. While the indicator lights are active, the

symbol will flash on the driver display.

Move the left stalk upward/downward slightly to activate the indicator lights on the right/left side of the car for three flashes.

Move the left stalk upward/downward until it stays in place to activate the indicator lights on the right/left side of the car continuously.

Note: Do not block the rain and light sensor in the center of the upper section of the windshield. Doing so could prevent the auto light or auto wiper functions from working properly.

Center display light controls

Some lights are only controlled through the center display. To toggle a light function on/off:

Navigate to

>Lighting>Exterior.

Press the corresponding button.

Function	Description
Auto lights	Automatically turns on the low beam, position lights, and license plate lights when the ambient light is low.
Low beam	Turns on the low beam, position lights, and rear license plate lights. When the low beam is active, the greensymbol is shown on the driver display.
Position lights	Turns on the position lights and the license plate lights. When the position lights are active, the greensymbol is shown on the driver display.
Rear fog light	The rear fog light makes it easier for other road users to see the car from behind. The rear fog light is stronger than the normal rear lights. It should only be used temporarily in situations with highly reduced visibility, such as when driving in fog. When the rear fog light is active, the yellowsymbol is shown on the driver display.
Adaptive headlights	Automatically changes the shape of the low beam according to the road type.
Approach light	When approaching the car at an approximate distance of 8-15 m with the digital key active on any unit, the low beam and the position lights automatically turn on. The approach light is also turned on when the car is unlocked.
Follow me home	Keeps the low beam and the position lights on for a pre-set time after exiting the car.
Charging indicator	Turns on the charging indicator light for two minutes after charging starts.

Note: The rear-fog light can only be turned on when the low beam

function is active.

Hazard warning lights

The hazard warning lights are used to warn other road users about traffic accidents or emergencies. When the hazard warning lights are active, the

and

symbols continuously flash on the driver display.

In case of a collision, the hazard warning lights will usually activate automatically. If the hazard warning lights do not turn on automatically, or if it is necessary to turn them on for another reason, press the hazard warning lights button on the overhead console to turn on/off the hazard warning lights.

Note: The hazard warning lights can be turned on (and remain on) even when the engine is off, without a key in the car, and with the car locked.